Study of The Extrusion and Painting Process of Aluminum Profiles of a Metal-Mechanical Industry Located in the South of Santa Catarina
DOI:
https://doi.org/10.31686/ijier.vol10.iss7.3817Keywords:
Quality management, Productive system, Aluminum Extrusion, Quality toolsAbstract
In the competitive scenary of the 21st century, organizations need to deal with the reality that in order to obtain an above-average return, it is necessary to be willing to meet high quality standards. This article consists of studying the extrusion and painting processes of an aluminum profiles and frames manufacturer, located in the south of Santa Catarina, in order to analyze and measure, through the use of quality tools and statistical software, faults and errors arising from this process. In this context, the research methodology adopted for this study is characterized as exploratory-descriptive, with a quantitative character. The methodological procedure started with an analysis and mapping of the extrusion and painting processes of aluminum profiles, seeking and interpreting information relevant to the study. Then the data was collected and analyzed, where it was possible to apply the Pareto Diagram and identify the most frequent non-conformities. A statistical analysis was then performed using the IBM Statistical Package for the Social Sciences (SPSS) version 21.0 software, comparing and associating the collected data in order to identify and understand the root causes of the defects that occurred. With the results obtained from the analyzes carried out, it became possible to draw up an action plan, using the 5W2H quality tool, containing suggestions and proposals for improvements, with a focus on reducing the scrap generated from the defects identified in the processes of extrusion and painting of aluminum profiles.
References
ABAL - Associação Brasileira do Alumínio. Guia técnico do alumínio: Extrusão. 4 ed. v. 1. São Paulo: ABAL, 2008.
BRESCIANI FILHO, E., SILVA, I. B., BATALHA, G. F., BUTTON, S. T. Conformação Plástica dos Metais. 6 ed. São Paulo: EPUSP, 2011.
CAMPOS, Vicente Falconi. TQC: controle da qualidade total (no estilo japonês). 9. ed. Nova Lima, MG: Falconi, 2014.
CARPINETTI, Luiz Cesar Ribeiro; MIGUEL, Paulo Augusto Cauchick; GEROLAMO, Mateus Cecílio. Gestão da qualidade ISO 9001:2008: princípios e requisitos. 4. ed. São Paulo: Atlas, 2011.
CARVALHO, Marly Monteiro de; PALADINI, Edson P. Gestão da qualidade: teoria e casos. 2. ed. rev. e ampl Rio de Janeiro: Elsevier, 2012.
DIETER, G. E. Metalurgia Mecânica. 2 ed. Rio de Janeiro: Guanabara Dois, 1981.
GIL, A. C. Métodos e técnicas de pesquisa social. 6. ed. São Paulo: Atlas, 2008.
GUIMARÃES FILHO, L.P. Programação de atividades para subempreiteiros de pequenos serviços: proposta baseada em estudo de caso. Dissertação apresentada ao programa de Pós-Graduação em Engenharia de Produção da Universidade Federal de Santa Catarina. Florianópolis, 2003
JURAN, J. M. A qualidade desde o projeto: novos passos para o planejamento da qualidade em produtos e serviços. São Paulo: Cengage Learning, 2009.
MACEDO, André Luiz Oliveira; CAMPOS, Renato Ramos. Diagnóstico do complexo metalmecânico: Brasil e Santa Catarina. Revista de Tecnologia e Ambiente, Criciúma, 2001.
PALADINI, Edson P. Gestão da qualidade: teoria e prática. 3. ed. São Paulo: Atlas, 2012.
SILVA, Damião Limeira da; LOBO, Renato Nogueirol. Gestão da qualidade: diretrizes, ferramentas, métodos e normatização. 1. ed. São Paulo: Érica: Saraiva, 2014.
SILVA, E. L.; MENEZES, E. M. Metodologia da Pesquisa e Elaboração de Dissertação. 4. ed. Atualizada e revisada. Florianópolis: 2005. 138 p.
TOLEDO, José Carlos de; BORRÁS, Miguel Ángel A.; MERGULHÃO, Ricardo Coser; MENDES, Glauco H. S. Qualidade: gestão e métodos. Rio de Janeiro: LTC, 2014.
VIEIRA FILHO, Geraldo. Gestão da qualidade total: uma abordagem prática. Campinas: Editora Alínea, 2003.
Downloads
- PDF 166 193
Published
Issue
Section
License
Copyright (c) 2022 Alice Ferraz de Souza, Kristian Madeira, Vilson Menegon Bristot, Milla Lúcia Ferreira Guimarães, Márcio Carlos Just, Leopoldo Pedro Guimarães Filho
This work is licensed under a Creative Commons Attribution 4.0 International License.
Copyrights for articles published in IJIER journals are retained by the authors, with first publication rights granted to the journal. The journal/publisher is not responsible for subsequent uses of the work. It is the author's responsibility to bring an infringement action if so desired by the author for more visit Copyright & License.
How to Cite
Accepted 2022-06-24
Published 2022-07-01
Share
Most read articles by the same author(s)
- Vilson Menegon Bristot, Leopoldo Pedro Guimarães Filho, Sara Pizzolo Silva, Vilmar Menegon Bristot, Edson Uggioni, Analysis of the Quality Indicator of the Paint Process of a Metalmechanical Industry , International Journal for Innovation Education and Research: Vol. 7 No. 4 (2019): International Journal for Innovation Education and Research
- Liege Mazo de Souza Tesserolli, Anabel Machado de Bem, Marinara Dagostin da Silva, Carolina Michels, Kristian Madeira, Cristina Keiko Yamaguchi, Dr. Gustavo Feier, Blood alcohol level and toxicologic test in drivers killed in road traffic accidents in the coal region of Santa Catarina State, Brazil , International Journal for Innovation Education and Research: Vol. 10 No. 8 (2022): International Journal for Innovation Education and Research
- Karine Ramos, Vilson Menegon Bristot, David Batista Gesuíno, Márcio Carlos Just, Bruno Brogni Uggioni, Vilmar Menegon Bristot, Richard Oliveira Cardoso , Edimar Kalfeld , Leopoldo Pedro Guimarães Filho, Application of AHP Method to Aid Destination Choice of Pre-Production Models in a Textile Industry , International Journal for Innovation Education and Research: Vol. 7 No. 10 (2019): International Journal for Innovation Education and Research